Soundstream bx 10 x install#

Input should match the source, and output should match the sensitivity of the host. Check that the input and output levels are set correctly.If you experience high audible distortion or low output volume: Check that the fuse is functioning correctly.Check power wire is correctly connected and have the appropriate potential (11- 16 volts).Check and make sure that B+ and GND are not reversed.Troubleshooting Guideį the unit does not turn on and the power indicator LED is NOT illuminated, start with this: Factory settings usually work just fine we recommend you try that first. You may change these jumpers to higher or lower settings to maximize your bass output and protect your speakers. The Bass Maximizer circuit can either increase or decrease the signal voltage to your liking. Bass Output Control Jumpers: Not all systems are designed the same some systems are designed strictly for SPL (Sound Pressure Level) while others a little tamer.Ground connections make sure your system is of before making this change. To help this situation, we have provided alternative Ground Isolation Jumper: Occasionally, an alternator whine may appear in a system because the source units and amplifiers have different grounds.In some scenarios, the source unit may look for ground through the RCA connectors even you should change the jumpers to the UNBALANCE position. ) Input Ground: For the Most system, you can leave this jumper set in the BALANCE position.Bass Maximizer Indicator: These three LED indicators flash when the bass.Often a higher frequency sounds louder and cleaner. If you want to protect your speaker system, even more, you should try a higher frequency. On most systems, setting the switch at 33Hz is fine. This PFM Subsonic Filter Switch comes with three frequency selections 35Hz / 50Hz / 80Hz. The PFM Subsonic Filter Switch: The BX-10 utilizes a PFM Subsonic Filter Switch, which will help with speaker control and amplifier power management.The WIDE knob adjusts how wide of a frequency range the BX-10 will effect. The SWEEP knob allows you to pick the center frequency that you want the BX-10 bass restoration circuit to maximize. Para-Bass Controls: These two knobs control the Para-Bass functions of the BX-10.Outputs: These RCA connectors should be connected to the next component after the BX-10, such as crossover, equalizer, or amplifier.They are also designed to handle very high signal voltages up to 15 volts. Input: The inputs of the BX-10 use a balanced input to help minimize induced noise.5V peak Frequency Response 10Hz – 100KHz +/-1dB Total Harmonic Distortion 0.003% Signal to Noise Ratio -130dB Balanced Input Noise Rejection _ >60dB Input Impedance 10K Ohm Output Impedance 150 Ohm Power Supply High headroom PWM Power Draw 150mA Fuse Rating 1Amp (Included) Product Functions Settings Amplifier Input Voltage Minimum Speaker Size 2.5 Volts 3V or Less 8” Subwoofers 5.0 Volts 5V or Less 10” Subwoofers 7.5 Volts 7V or Less 12” Subwoofers 10 Volts OH MY GOSH!!!!!!!! SPL Type Subwoofers Product Specifications Maximum Input Level 15V rms Maximum Output Level 13. It is recommended: listen using the factory setting before changing your Bass Output settings.

If you should need to change the settings, please use the chart below for guidance. This device is equipped with several different Bass Output selections.

Picture to help illustrate input and outputs Setting the Bass Output Control.

Soundstream bx 10 x install#

(Dash Remote) – This is your knob, wait… you know what we mean?! Connect provide dash level controller and provided cable to install somewhere in drivers Make sure and measure and purchase separately (Output) – This should be connected to your bass amplifiers this kit does not come with any RCA’s cables. (Balanced Input) – Connect your Low-Level signal from your vehicle’s source unit or input converter if you are not using an aftermarket radio.

ConnectionsĬonnect to amplifier Turn-On – Behind Radio or True Ignition Source On the Chassis of the BX-10, three LED indicators flash when the bass maximization circuit is activated. Not only does the BX-10 provide great music to your ears, but it gives you the same visual enjoyment as well.